Forum Post: RE: level of
Nadeem, in your original post you mentioned having an idea for Drawing Extraction but in your last response you mentioned DVs instead. Can you confirm which you are using?
View ArticleForum Post: RE: Hypermodeling ?
Eric, If you use the Create Drawing dialog and omit the sheet model: then you end up with drawing models ready for placement on sheets. You could use the dialog to create the sheets as well, then once...
View ArticleForum Post: RE: detailingsymbol.dll lost
Hi Thomas, It sounds like Avast has mistakenly quarantined the relevant files. Did you find any in the quarantine location?
View ArticleForum Post: Door wall sides
It is probably obvious, but what is the way to get a wall to turn 90º on a door (or window) side? I don´t want the brick to be seen, I want the plasterboard to cover door sides. It is some door...
View ArticleForum Post: Callouts / coordinate system
Placing plan callouts in models is always done parallel to global coordinates, regardless of the orientation of the active coordinate system. Is this intended, or not? I'm asking because I have a...
View ArticleForum Post: RE: Wrong Space Label
There are various ways of solving the issue of displaying Space tags in the model. The first is to use Hypermodeling. Assuming you've created a drawing from your model, then hover over the marker for...
View ArticleForum Post: RE: PCStudio, Edit Component Dialog, and Positioner Preferences
Steve, Thanks for the quick reply. I'm hoping someone can weigh in on the Advance section of the Positioner Snap Preferences and "Add Remove World Normal Angle" and "Suppress Plane-Plane on First...
View ArticleForum Post: RE: PCStudio - How do you swing your doors?
Steve, Thanks for having a go at answering my question. However, I posed my question so poorly that you didn't stand a chance in Heck of giving me anything like the answer I'd hoped for. So, let me...
View ArticleForum Post: RE: detailingsymbol.dll lost
Thanks for answers. I did excluded AdfTINModeler.dll and PrintCadHandler. And printing seems ok now. I have the free version of Avast and right now I can't find the quarantine location. Think I found...
View ArticleForum Post: RE: Door wall sides
In my mind this is more of a detail question than a graphics or modeling question. 1) You can make the frame deeper by increasing the dimension or setting it to match wall. 2) You can, as you...
View ArticleForum Post: RE: detailingsymbol.dll lost
Well deleting the prefs folder (or more precisely - the content of it) didn't do any difference. The first four buttons in Drawing composition, R1, R2, R3, R4 are dead. But R5-Create plan seems to...
View ArticleForum Post: RE: detailingsymbol.dll lost
Seems I have exactly the same problem in a ss5 test install I have.
View ArticleForum Post: RE: Door wall sides
I see. So there´s no automatic solution, as I expected. I´ll try the Assembly tool, but I fear that this corrections are usable only with special cases. It is not a factible solution, let´s see, for...
View ArticleForum Post: RE: Beam properties & annotations
As I'm sure you're aware, you can auto-annotate TOS and BOS values for beams using drawing rules. But it sounds as though you want the ability to do this manually as well? For columns, are top and...
View ArticleForum Post: RE: Aecosim stopped recognising mapped drives!!
This certainly seems to be a system level issue based on what you've described, but I don't recall coming across anything similar. Based on the fact that MicroStation still recognizes them, I'm...
View ArticleForum Post: RE: Deprecate non-datagroup properties
The properties in that panel do exist in both the DataGroup System (as you've shown) and in the Building Element Info tool (their original location). However, you can certainly change them both...
View ArticleForum Post: RE: Door wall sides
Pedro, I'm not sure which metric DataSet you are working with, but as far as I know for some time now they the doors have the option to set them to the wall width or alternately to a user specified...
View ArticleForum Post: RE: Aecosim stopped recognising mapped drives!!
Duncan Gammie my drives are shown unavailable, marked with red x's. However, if I navigate to any of them, they will open. Hi Duncan, Please can you post a screen shot of this? Have you discussed with...
View ArticleForum Post: RE: Aecosim stopped recognising mapped drives!!
Marc, screenshot of microstation manager attached. I will try your suggested solution later today and get back to you.
View ArticleForum Post: RE: Aecosim stopped recognising mapped drives!!
That's what I was seeing, it was a test so I didn't investigate further at the time. Are these icons only showing up in AECOsim?
View Article