Forum Post: RE: Another Cut Solid by Curve Issue
Ok, I understand what's going on now. Thanks for your help.
View ArticleForum Post: RE: Another Cut Solid by Curve Issue
I just opened the dgn from april 3rd and set the display mode to wireframe. There is no difference between the curve and the edge of the solid model. There is only a small difference between the curve...
View ArticleForum Post: RE: Another Cut Solid by Curve Issue
Oh ok, I hadn't looked at that, I'll keep that in mind for the future. Thanks
View ArticleComment on VBA errors when using certain Structural or Mechanical tools
I guess Steve was in a bit of a rush to get this out. The intent was probably either ...nor does Bentley recommend "not installing" or "uninstalling".... "Solution 3 Note: Uninstalling any of the...
View ArticleComment on VBA errors when using certain Structural or Mechanical tools
That typo, at least I assume it's a typo, was already in the original version, my bad Steve.
View ArticleWiki Page: Remove 'Orphaned' Floor Manager Elements
Applies To Product(s): AECOsim Building Designer Version(s): 08.11.09.735 and above Environment: N/A Area: Floor Management Subarea: Original Author: Marc Thomas, Bentley...
View ArticleForum Post: Re-symbolization of Duct with Internal Lining - ABD 593
When acoustically lined ductwork is re-symbolized in the DV drawings model, only the straight pieces of duct in any lined system display the dashed line representing liner. That is, none of the lined...
View ArticleForum Post: RE: Centerline Width
yea... Hopefully Vancouver will have an update to Linestyles, enhance Annotation Scale to work with patterns/hatches, and the new PCM will be able to generate parametric cells that can be used to feed...
View ArticleForum Post: Apply Datagroup Data to an Element
Hi all, It's peharps a stupid question, but I don't found the Tool or the Rule. If I draw a "Wall" with the old "TriForma tools" Form Modeling, I can Use Apply Part but, I can't Modify Properties (No...
View ArticleForum Post: RE: Apply Datagroup Data to an Element
Hi Francois, I never used it, but theoretically you should try "add instance data" from the Toolbox "Data Group System". Christian
View ArticleForum Post: RE: Apply Datagroup Data to an Element
Hi Christian, You're Right Thank You François
View ArticleForum Post: Level overrides in dwgs
Using ABD ss4 and in a dwg I apply level overrides (colour) on a referenced dwg. It works first, but if I turn ref display off and on the setting is lost. Just me? or?
View ArticleForum Post: RE: Drawing View Levels Off
I tested this issue further and found that if you turn off the levels you do not want to display in the drawing view, from the 3D model view window where the actual Callouts are placed, then those...
View ArticleForum Post: RE: Slab Penetrations Tool- Problems with extractions
There is an "Include Constructions" setting in the DEM dialog Participants tab that may also help.
View ArticleForum Post: RE: SS5 / VBA errors after installation of Structural...
OT: Did this have any effect on the crashes you were getting when opening ABD Ss5?
View ArticleForum Post: RE: SS5 / VBA errors after installation of Structural...
You mean the one Windows 8.1 PC in our office? I've commented that one on the Service Request already - no unfortunatly not, this didn't have any effect.
View ArticleForum Post: RE: Level overrides in dwgs
Are you in a dgn or a dwg file? If you are in a dwg file, it's not possible to save the overrides, as the dwg format isn't capable of saving that information.
View ArticleForum Post: RE: Slab Penetrations Tool- Problems with extractions
We've also had this problem before, not lately. I think the problem is which object you use for cutting. If you use a paz-cell, and you have visible geometry in the cell where the cut is, it might...
View ArticleForum Post: RE: install AECOsim
Apparently I'm not the only one with problems related to VBA. "Wouldn't have happened with Linux" comes into my mind...
View Article